This guide is for anyone who is new to NMEA 2000 and wants to quickly understand the key issues in building an NMEA 2000 network. It is not the most in-depth technical article on the subject, there are plenty of those online, but it focuses on giving you the core information you need to use the Digital Yacht range of NMEA 2000 cabling products to create or expand your NMEA 2000 network.
NMEA 2000 Networking Guide
- NMEA 2000 is the marine version of the CAN networks found in every modern car.
- NMEA 2000 allows marine electronic devices from different manufacturers to talk to each other.
- NMEA 2000 is a standard set of data messages, protocols, and connectors that all NMEA 2000 devices must use.*
* Note – Some manufacturers have created their own “flavours” of NMEA 2000 with different connectors and cabling; Raymarine’s “SeaTalkNG” and Simrad’s “SimNet” are two examples and both need proprietary adaptor cables to connect to standard NMEA 2000 networks.
Connecting NMEA 2000 Devices
You cannot just plug two NMEA 2000 devices together with a suitable NMEA 2000 cable – they must be connected to a properly constructed NMEA 2000 network.
- Each device has an NMEA 2000 interface that must be powered from the network
- Some smaller low power devices, like sensors, are also powered from the network
- There is a small cost in setting up the network, but future expansion is very easy
- A NMEA 2000 Starter Kit is a cost-effective way to build a small, expandable network
An NMEA 2000 Starter Kit
Kit contents:
- 4-way T-Piece Backbone
- 2x Terminators
- 1m Power Cable (fused)
- 1m Drop Cable
The part number is ZDIGN2KIT and if you want to find out more about the Digital Yacht NMEA 2000 Starter Kit, please click here.
Basic NMEA 2000 Networking Rules
The list below gives you all the key NMEA 2000 networking rules that, if followed, will ensure your NMEA 2000 network works correctly:
- The network must be properly terminated; only two terminators fitted, one at each end of the backbone
- The NMEA 2000 supply voltage must be between 9V and 16V
- The NMEA 2000 supply current must be less than 3A (60 LEN)
- Maximum number of 50 physical devices on the network
- The NMEA 2000 backbone must be less than 100m
- Maximum single drop cable length is 6m
- Total length of all drop cables must be less than 76m
- The voltage drop from one end of the network to the other must be less than 1.5V
NMEA 2000 Network Current
A key consideration in any good NMEA 2000 network design is the total current that the network is consuming. If the total current exceeds the safe current capacity of the NMEA 2000 cabling (3A for all Digital Yacht cables), the cable could melt or even cause an electrical fire.
- Each device on the NMEA 2000 network consumes some current
- It is very important that the total network current is known and is less than 3A
- Every NMEA 2000 certified device has a Load Equivalency Number, or “LEN” for short
- 1 LEN = 0.05A (50mA)
- The LEN number will be printed on the device’s product label
- Add up the LEN values of all devices and make sure the total is less than 60 LEN, which equals 3A
NMEA 2000 Network Voltage Drop
- When current flows through the NMEA 2000 backbone and drop cables, a voltage drop occurs, resulting in the voltage at one end of the network being different from the other end
- The longer the cables or the higher the current, the larger the voltage drop; if it exceeds 1.5V, data errors can occur
- To calculate voltage drop, use the following formula (valid for most NMEA 2000 networks):
Volt Drop = LEN x Backbone Length x 0.006
- If voltage drop > 1.5V, add an additional power insertion point (Power Cable) connected to the same 12V DC supply as other NMEA 2000 power cables, or move the existing power cable to the middle of the network backbone to reduce voltage drop
- Example: total backbone length = 10m, total LEN = 12
Volt Drop = 12 x 10 x 0.006 = 0.72V
This is well below the 1.5V maximum voltage drop, allowing good data communication.
NMEA 2000 Parts
Please note that all Digital Yacht “Drop Cables” can also be used as backbone cables and are easily connected together to make any length required.
Fault Finding an NMEA 2000 Network
NMEA 2000 networks are very reliable and really are “Plug and Play.” When things go wrong, it is not always easy to fault-find, even on a small network.
NAVDoctor is the perfect NMEA 2000 diagnostic tool for dealers, installers, and boat builders. It turns any mobile device into an NMEA 2000 network analyser, creating simple and clear web pages that show the health and status of your network.
The part number is ZDIGNAVDOC. To find out more about the NAVDoctor Diagnostic tool, please click here.
